Corrosion behaviour and mechanism of 6082 aluminium alloy in NaCl and Na2SO4 etchants

The corrosion behaviour of 6082 aluminium alloy was studied by measuring the electrochemical impedance spectra and electrode polarization curves. After the electrochemical tests, a microstructural analysis of the samples was conducted by using optical microscopy and electron scanning microscopy techniques to determine the corrosion mechanism. The results show that the Nyquist plot of the electrochemical impedance data in the NaCl solution consists of high- and low-frequency capacitive impedance loops. When ions are added to the NaCl etchant, the Nyquist plots of the electrochemical impedance data are composed of two different curves: a high-frequency capacitive impedance loop and a low-frequency inductive impedance loop. The corrosion current density increases with increasing concentration, and as a result, the corrosion resistance of the aluminium alloy decreases. The microstructures of 6082 aluminium alloy consist of Mg₂Si secondary particles in a large α-Al matrix. Pitting corrosion initially occurs at the boundary between the matrix and secondary particles because the electrode potentials of the matrix and secondary particles are different. Then, corrosion paths develop along the network-like grain boundaries, and finally, massive network-like corrosion occurs throughout the entire alloy.     

Microstructure and corrosion behaviors of FeCrNiBSiMox stainless steel fabricated by laser melting deposition

In this paper, FeCrNiBSiMo_x (x = 1.0, 1.5, 2.0, 2.5) stainless steels were successfully prepared using a laser melting deposition technology, with the aim to investigate the effect of Mo content on microstructure and corrosion behaviors. The results showed that the as-deposited specimens were composed mostly of α-Fe and a small amount of (Cr, Mo)₇C₃, and (Cr, Mo)₇C₃ existed in the inter-dendritic (ID) region. As the Mo content increased, grain refinement could be clearly observed, and the area of the ID region increased from 27% to 54%. The low-angle boundaries accounted for 60–70% of the grain boundaries of the as-deposited specimens. Increasing the content of Mo improved the microhardness of the as-deposited specimens from 652 HV to 813 HV. The corrosion current density of the as-deposited specimens with the Mo mass fractions of 1.0%, 1.5%, 2.0%, and 2.5% were 1.37 × 10⁻⁶, 1.02 × 10⁻⁷, 6.19 × 10⁻⁷, and 3.06 × 10⁻⁷ A/cm², respectively. The as-deposited specimen with Mo content of 1.5% had lower cumulative erosion loss and erosion loss rate than other as-deposited specimens. The FeCrNiBSiMo_x (x = 1.5) specimen exhibited excellent resistance to electrochemical corrosion and cavitation erosion.     

Synergistic effect of iodide ions and bark resin of Schinus molle for the corrosion inhibition of API5L X70 pipeline steel in H2SO4

The synergistic effect of bark resin of Schinus molle (BRSM) and iodide ions in 0.5 M sulfuric acid has been studied for the first time by potentiodynamic polarization and electrochemical impedance spectroscopy measurements; also, the surface morphology has been analyzed by scanning electron microscopy–energy-dispersive X-ray spectroscopic analysis in the present work. The results show that the BRSM and iodide ions have an evident synergistic inhibition effect in a 0.5-M sulfuric acid solution. The adsorption of the BRSM/iodide ion system follows the Langmuir adsorption isotherm and acts as a mixed-type inhibitor in sulfuric acid. The BRSM/iodide ion system is an effective inhibitor for API5L X70 pipeline steel in the 0.5-M sulfuric acid solution. The maximum percentage inhibition efficiency is equal to 99% at 1 g/L BRSM + 2 mM KI.     

变质胺液净化复活技术进展

用于脱硫及脱碳的胺液在长期使用中因降解或杂质混入发生变质，导致脱硫脱碳效率下降、胺液发泡、装置腐蚀及能耗增大等系列问题，而胺液净化复活技术是解决胺液系统问题的有效手段。本文从变质胺液中污染物出发，分别总结了固体颗粒物、烃类及表面活性物质、胺变质产物及热稳定盐的成因、危害及其控制手段。针对热稳定盐等重点难处理污染物，主要介绍了蒸馏回收、离子交换以及电渗析等净化技术的技术原理及国内外研究与应用概况，并对技术特点进行总结分析。最后通过技术对比指出，电渗析因具备胺液回收率高、热稳定盐净化深度高、能耗适中、产生少量易处理污染物等特点，是我国在胺液净化复活技术领域最具潜力的发展方向。     

Discovery of the Tiancilactone Antibiotics by Genome Mining of Atypical Bacterial Type II Diterpene Synthases

Although genome mining has advanced the identification, discovery, and study of microbial natural products, the discovery of bacterial diterpenoids continues to lag behind. Herein, we report the identification of 66 putative producers of novel bacterial diterpenoids, and the discovery of the tiancilactone (TNL) family of antibiotics, by genome mining of type II diterpene synthases that do not possess the canonical DXDD motif. The TNLs, which are broad‐spectrum antibiotics with moderate activities, are produced by both Streptomyces sp. CB03234 and Streptomyces sp. CB03238 and feature a highly functionalized diterpenoid skeleton that is further decorated with chloroanthranilate and γ‐butyrolactone moieties. Genetic manipulation of the tnl gene cluster resulted in TNL congeners, which provided insights into their biosynthesis and structure–activity relationships. This work highlights the biosynthetic potential that bacteria possess to produce diterpenoids and should inspire continued efforts to discover terpenoid natural products from bacteria.     

A reference isotope dilution headspace GC/MS method for the determination of nitrite and nitrate in meat samples

A novel method for the determination of nitrite and nitrate in meat products is presented. The samples were ground and extracted in hot water with the presence of and internal standards. The solution was buffered with sodium bicarbonate and reacted with triethyloxonium tetrafluoroborate to convert nitrite and nitrate into EtNO₂ and EtONO₂. Such derivatives could be detected by headspace GC/MS in positive chemical ionisation mode with 0.05 µg g⁻¹ and 1.0 µg g⁻¹ LOD. The method was used for and quantitation in the 0.5-300 and 2.5-300 µg g⁻¹ ranges. The method was applied for the analysis of fifteen meat products. Despite minimal sample preparation, the headspace sampling ensured a clean chromatography for over 135 analyses (throughput ten samples per hour). The proposed method offers selective GC/MS detection combined with high-precision isotope dilution calibration, it is suitable for metrological applications and can support regulations on meat safety (European Commission, 2011).     

C/C-SiC component for metallic phase change materials

Thanks to their high energy density and thermal conductivity, metallic Phase Change Materials (mPCM) have shown great potential to improve the performance of thermal energy storage systems. However, the commercial application of mPCM is still limited due to their corrosion behavior with conventional container materials. This work first addresses on a fundamental level, whether carbon-based composite-ceramics are suitable for corrosion critical components in a thermal storage system. The compatibility between the mPCM AlSi₁₂ and the Liquid Silicon Infiltration (LSI)-based carbon fiber reinforced silicon carbide (C/C-SiC) composite is then investigated via contact angle measurements, microstructure analysis, and mechanical testing after exposure. The results reveal that the C/C-SiC composite maintains its mechanical properties and microstructure after exposure in the strongly corrosive mPCM. Based on these results, efforts were made to design and manufacture a container out of C/C-SiC for the housing of mPCM in vehicle application. The stability of the component filled with mPCM was proven nondestructively via computer tomography (CT). Successful thermal input- and output as well as thermal storage ability were demonstrated using a system calorimeter under conditions similar to the application. The investigated C/C-SiC composite has significant application potential as a structural material for thermal energy storage systems with mPCM.     

热处理对等离子喷涂铁基非晶合金涂层微观结构和耐腐蚀性能的影响

采用等离子喷涂技术在Q235钢基体上制备Fe48Cr15Mo14C15B6Y2非晶合金涂层,之后对涂层进行200,300,500,600,700℃热处理,研究了热处理对涂层微观结构、耐电化学腐蚀性能和耐均匀腐蚀性能的影响。结果表明:随着热处理温度的升高,涂层的非晶含量降低,孔隙率先减小后增大,经300℃热处理后涂层的孔隙率最低,且低于未热处理涂层的;热处理后涂层中的晶体相主要包括α-Fe,Fe-Cr,Fe63Mo37,Fe3C等;随着热处理温度的升高,涂层的自腐蚀电流密度先减小后增大,经300℃热处理后,自腐蚀电流密度最小,涂层的耐电化学腐蚀性能最好;经过热处理后,涂层在NaCl溶液中浸泡31d后的单位面积质量损失减小,且热处理温度越高,单位面积质量损失越小,涂层的耐均匀腐蚀性能提高。     

Comparative study of Ti-C-Ni-Al,Ti-C-Ni-Fe,and Ti-C-Ni-Al/Ti-C-Ni-Fe coatings produced by magnetron sputtering,electro-spark deposition,and a combined two-step process

Comparative study of Ti-C-Ni-Fe, Ti-C-Ni-Al, and Ti-C-Ni-Al/Ti-C-Ni-Fe coatings obtained by electro-spark deposition (ESD) using TiCNi electrode, magnetron sputtering (MS) of TiCNiAl target, and a combination of these methods (MS-ESD) was carried out. The coating microstructures and elemental compositions were studied by means of X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and glow discharge optical emission spectroscopy. The materials were tested in terms of their hardness, elastic modulus, elastic recovery, crack resistance, friction coefficient, and wear resistance under sliding, impact and abrasive conditions, as well as corrosion- and oxidation resistance. The work demonstrated that the utilization of a combined two-step MS-ESD technology permits to obtain bilayers made of Ti-C-Ni-Al/Ti-C-Ni-Fe coatings with improved crack-, wear- and oxidation resistance compared with their single-layered Ti-C-Ni-Al counterparts deposited by MS, and with reduced friction coefficient and enhanced corrosion resistance compared with ESD Ti-C-Ni-Fe coatings.